Long Arms, High Hips, Strong Deadlifts

By Myles Kantor

For www.EliteFTS.com

 

 

“On the weightlifting platform, your physical strength has to be multiplied by your intellectual abilities and ambitions.” —Anatoly Pisarenko

Barbell training is both a passion and a discipline. A world of physical complexity underlies the constructive ardor of heavy squatting, pressing, and deadlifting. As one advances in barbell training, respect for that complexity becomes increasingly important. No lift embodies this combination of intensity and complexity like the deadlift.

Legendary powerlifter, Ed Coan, remarks in his video on the deadlift: “The deadlift is the number one technique lift. If you don’t have technique in the deadlift, you just can’t muscle it up” (1). Coan’s attribution of technical primacy to the deadlift might be surprising. There seems to be an attitude among some lifters that deadlifting is basically just about attitude and the least technical of lifts. It’s true that all of the technical perfection in the world means nothing if someone lacks the volition to break a maximal weight off the floor and force it to lockout. However, all of the intensity in the world won’t surmount lousy technique with a truly maximal weight.

By “truly maximal,” here’s what I mean. Let’s say a guy grinds out a deadlift in a manner nothing short of repugnant—lower back extremely rounded, bar over the toes at the start, bar jerked up with no leg drive. I submit that was not a maximal weight. It was a submaximal weight made maximal in effort due to severe inefficiencies.

Consider if you loaded a bar to 85 percent of your best deadlift. Rather than deadlift it properly, do it like the aforementioned fool. I’m guessing the weight would feel less like 85 percent and more like 95 percent or higher. What this means is that bad technique amounts to increasing the weight on the bar. When the weight is 100 percent and the inefficiencies are severe, the results will be failure and often injury.

Utter technical repugnance usually isn’t the problem with powerlifters. We tend to miss deadlifts due to comparatively small but pernicious errors that kill third attempts. With conventional deadlifters, it’s usually starting with the bar forward of the middle of the foot, which places the shoulder blades behind the bar. This produces a gruesome cluster of inefficiencies.

As Mark Rippetoe and Lon Kilgore analyze in Starting Strength: Basic Barbell Training and video data confirm, on a heavy deadlift, the bar isn’t going up until it’s over mid-foot and aligned with the shoulder blades. Being compelled into this equilibrium wastes precious energy and endangers the body versus starting in that equilibrium. Coan makes a similar point in his deadlift video involving one’s center of gravity. Dave Tate has remarked, “The stronger you get, the more important technique becomes, and one inch can make the biggest difference in the world” (2). (An easy way to think of the bar-to-foot relationship is to see where the bar is at lockout in relation to the foot. Given that the bar is over the middle of the foot at lockout, why not start there? Why add a horizontal component to a vertical lift? I recently facilitated a 50-lb PR in a couple of minutes with this explanation.)

On the other hand, it’s rare to see a sumo deadlifter start with the bar much forward of mid-foot. Probably due to the greater amount of toe flare and lateral knee movement with sumo, starting with the bar much forward of mid-foot feels immediately wrong. The sumo deadlifter makes a different error shared by many conventional deadlifters as well—excessive knee bend.

Excessive knee bend causes several problems, most apparently with hip position. Tate notes, “…look at your hip position at the start of the lift when you pull and watch how much your hips move up before the weight begins to break the floor. This is wasted movement and does nothing except wear you out before the pull” (3). Powerlifter, Rick Walker, makes another key point: “When I would sumo deadlift, I was always trying to keep my back perfectly upright, which in turn, caused me to sink my hips very low. Now I’m five feet nine inches, but I have a wing span of 74 inches. It was ridiculous for me to sink my hips so low when I had that much of an advantage with arm height” (4).

Moreover, when the hips are too low at the start, this causes the shoulder blades to move behind the bar and often moves the bar forward of mid-foot if the shins bump the bar (more likely with conventional deadlifters). Coan himself started with quite low hips on his heavy deadlifts (not on initial warm ups though). When the bar actually left the floor, his hips were considerably higher with a different torso position than at the start.

Here’s another way to think of it. Excessive knee bend shortens one’s arms. A gifted bench presser with short “alligator” arms runs into a less comfortable situation when the bar hits the floor. He has no choice but to get low to reach the bar, his hip depth approximating a full squat in the start position. Why would a person with more advantageous arm length do this? The benefit of keeping the arms as “long” as possible is more obvious when they’re artificially shortened in a deficit deadlift variation like the snatch-grip deadlift. The snatch-grip deadlift can be an excellent assistance exercise, but it’s not meant to be done in a meet.

How does one prevent excessive knee bend and maximize arm length? Get into your deadlift stance. Lean over and bend your knees as much as it takes to grip the bar. Now squeeze up your chest hard, and you’re all set.

This is the set up of Andrey Belyaev, perhaps the most impressive powerlifter of our era:

 

When Ismo Lappi deadlifted a world record 749 lbs in the 165-lb weight class in 2001, he similarly maximized his arm length:

 

In this case, Lappi takes in his air and sets his back before descending. He bends his knees as much as it takes to grip the bar and then starts the lift. Note how high Lappi’s hips are at 17 seconds at the start. For a variation of this style involving a pre-stretch of the hamstrings, see six time IPF world champion, Viktor Furazhkin:

 

These elite lifters share some fundamental characteristics at the start of their deadlifts—hips high, arm length maximized, shins very close to the bar, and torsos not vertical. This network of efficiency prevents wasted movement and enables the display of amazing strength.

“There are a lot of strong people who aren’t as effective as they should be,” Mark Rippetoe once told me. We were discussing people who train intensely but foolishly, suppressing their full potential. Sometimes that potential can be liberated through an inch of foot movement and a few degrees less knee movement. Sometimes an inch and a few degrees is the difference between failure and a PR.

References

  1. Coan Ed. The Deadlift. Quads Gym.
  2. Tate Dave. “Motivating Athletes.” CrossFit Journal interview, August 14, 2009.
  3. Tate Dave. “The Dead Zone.” T-Nation.com, January 31, 2002.
  4. Walker Rick. “On Chicken Sacrifice, Speed, and Deadlifts.” EliteFTS.com, April 5, 2007.

Myles Kantor is a personal trainer and powerlifter from Boynton Beach, Florida. He has competed in the APF and USAPL.

Elite Fitness Systems strives to be a recognized leader in the strength training industry by providing the highest quality strength training products and services while providing the highest level of customer service in the industry. For the best training equipment, information, and accessories, visit us at www.EliteFTS.com.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s